Not sure what material is best for your application?
Contact an Expert
Search By Material
Search By Application
Category Archives: Application
Q: We are looking for a very strong non-conductive M8 socket cap bolt that we can use to mount tooling on the end of a conveyor. There is a lot of leverage and force applied to these brackets and we were shearing off the Nylon bolts. Any suggestions? A: One of the … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Strength, Material Tagged PEEK bolts for high strength, PEEK bolts for high strength non-conductivity, PEEK screws for high strength, PEEK screws for high strength non-conductivity, PEEK screws for non-conductivity, PEEK socket head cap screws for high strength, PEEK socket head cap screws for non-conductivity, PEEK socket head screws for high strength, PEEK socket head screws for high strength non-conductivity, PEEK socket head screws for non-conductivity, PEEK socket heads for high strength non-conductivity Leave a comment
Q: We are in search for a bolt material that can handle sulfuric acid – compatible with 96% H2SO4. The exposure should be low and only on an infrequent basis. Also, these applications when H2SO4, DI Water is used to flush and clean off the surfaces during any maintenance that occurs inside the … Continue reading
Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners Tagged Hastelloy bolts in H2SO4, Hastelloy C276 bolts for H2SO4, Hastelloy C276 bolts in H2SO4, Hastelloy C276 for H2SO4, Hastelloy C276 in H2SO4, Hastelloy C276 screws for H2SO4, Hastelloy C276 screws in H2SO4, Hastelloy in H2SO4, Hastelloy screws in H2SO4 Leave a comment
Q: I’m looking to purchase some ¼-20 bolts/nuts/washers that will be suitable to fasten metal plate together at 1,300C. The fasteners need to last at least 4 minutes at this temperature but preferably longer. The load on the bolts will be very low. A: I think there are a couple … Continue reading
Posted in Application, FAQs, High Temperature Resistance Tagged Fast Delivery Ceramic Screws, Fast Delivery Inconel, Fast delivery Inconel bolts, Fast delivery Inconel screws, Fast lead time ceramic screws, Fast lead time high temperature fasteners, Fast lead time inconel bolts, Fast lead time inconel screws, Remove term: Fast lead time high temperature fasteners Fast lead time high temperature bolts, Remove term: Fast lead time high temperature fasteners Fast lead time high temperature screws Leave a comment
Q: We are looking to find an electrically non-conductive bolt that would also work at temperatures up to 500 F max. They will be used for an electrically live part isolation kit. Anything that will fit the bill? A: Without any understanding of your strength requirements, and focusing solely on the … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Non-Conductive Tagged PEEK bolts for high temperature non-conductivity, PEEK for high temperature non-conductivity, PEEK glass reinforced fasteners, PEEK glass reinforced nuts, PEEK glass reinforced screws, PEEK glass reinforced studs, PEEK glass-reinforced bolts, PEEK glass-reinforced fasteners for non-conductive, PEEK glass-reinforced screws for non-conductive, PEEK glass-reinforced studs for non-conductive, PEEK glass-reinforced studsfor non-conductive, PEEK screws for high temperature non-conductivity, PEEK studs for high temperature non-conductivity Leave a comment
Q: What does it mean for Inconel bolts to be produced per ASTM B637. A: The specification ASTM B637 is a raw material specification for both hot- and cold-worked precipitation-hardened nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Inconel 718 bolts are one of several age hardened nickel alloys … Continue reading
Posted in Application, FAQs, High Temperature Resistance, Specialty Metal Fasteners Tagged Inconel 718 bolts per ASTM B637, Inconel 718 bolts per B637, Inconel 718 nuts per ASTM B637, Inconel 718 nuts per B637, Inconel 718 per ASTM B637, Inconel 718 per B637, Inconel 718 screws per ASTM B637, Inconel 718 screws per B637, Inconel 718 studs per ASTM B637, Inconel 718 studs per B637, Inconel bolts per ASTM B637, Inconel bolts per B637, Inconel nuts per ASTM B637, Inconel nuts per B637, Inconel per ASTM B637, Inconel per B637, Inconel screws per ASTM B637, Inconel screws per B637, Inconel studs per ASTM B637, Inconel studs per B637 Leave a comment
Q: I need a flat head screw that is both non-Conductive Fastener and can survive shock and vibration. Any ideas? A: Polymers and ceramics are the only options for non-conductive screws. As ceramics are brittle, they would non withstand shock and vibration. In terms of polymers, PEEK is the go-to option … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Strength, Material Tagged Bolts for non-conductivity, non-conductive bolts, non-conductive screws, PEEK bolts for non-conductivity strength, PEEK bolts for strength in non-conductive environments, PEEK bolts for Vibration, PEEK fasteners for vibration, PEEK for non-conductivity strength, PEEK for strength in non-conductive environments, PEEK for vibration, PEEK screw for strength in non-conductive environments, PEEK screws for non-conductivity strength, PEEK screws for vibration, Screws for non-conductivity Leave a comment
Q: We are looking for screws to hold down electronic circuit boards. Unfortunately the mounting provisions need to be electrically isolated from the mounts. In addition, we need strength, non-conductivity, and impact resistance, even at cold temperatures (-40C). A: A great material to consider would be PEEK screws or PEEK with Glass Fiber reinforcement. These … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Strength, Non-Conductive Tagged PEEK for impact resistance, PEEK for strength in cold temperatures, PEEK for strength in subzero temperatures, PEEK for subzero temperatures, PEEK screws for electric insulation, PEEK screws for impact resistance, PEEK screws for non-conductivity, PEEK screws for strength in cold temperatures, PEEK screws for strength in subzero temperatures, PEEK screws for subzero temperatures Leave a comment
Q: I’m involved in is currently looking at your non-conductive fasteners to isolate an SMA Connector. But have several questions for finding the right solution regarding torque, preload heating and cooling, and locking features. A: Thanks for all the questions and interest. I will answer all your questions: How is torque … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, Material, Non-Conductive, Technical Questions Tagged Extreme Bolt offers Non-conductive bolts, Extreme Bolt offers Non-conductive fasteners, Extreme Bolt offers Non-conductive screws, non-conductive bolts, non-conductive fasteners, non-conductive screws Leave a comment
Q: Hi, I’m search to get a 1/4″-20 x 3ft long alumina ceramic rod. Is this something you can make? A: For Extreme Bolt & Fastener, 3″ long is the max length we can produce a ceramic bolt, rod or other fastener. As you may know ceramics are brittle, but breakage … Continue reading
Posted in Advanced Ceramic Fasteners, Application, FAQs, High Strength, High Temperature Resistance, Technical Questions Tagged how long can you make a ceramic bolt, How long can you make a ceramic fastener, How long can you make a ceramic screw, How long can you make a zirconia fastener, how long can you make a zirconia screw, How long can you make an alumina bolt, How long can you make an alumina fastener, How long can you make an alumina screw, Remove term: how long can you make a zirconia bol how long can you make a zirconia bolt, what is the max length of a alumina screw, what is the max length of a ceramic bolt, what is the max length of a ceramic rod, What is the max length of a ceramic screw, what is the max length of a zirconia bolt, what is the max length of a zirconia rod, what is the max length of a zirconia screw, what is the max length of an alumina bolt, what is the max length of an alumina rod Leave a comment
Q: I am designing an engine unit and am considering using 1.4980 stud bolts and nuts at elevated temperature. What is the maximum working temperature for stud bolts made of 1.4980 (A-286)? A: A286/Alloy 660 or 1.4980 fasteners are made of a stainless steel alloy which contains iron, nickel, and … Continue reading
Posted in Application, FAQs, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged 1.4980 bolts, 1.4980 bolts for high strength, 1.4980 bolts for high temperature strength, 1.4980 bolts for oxidation resistance, 1.4980 fasteners, 1.4980 fasteners for high temperature strength, 1.4980 screws, 1.4980 screws for high strength, 1.4980 screws for high temperature strength, 1.4980 screws for oxidation resistance Leave a comment
Q: What is the difference between bolting to SAE AS7466 and SAE AS7467? A: Both SAE AS7466 and SAE AS7467 describe bolts and screws made from Inconel 718 (UNS N07718) material equivalent to the European 2.4668 material norm. The main difference between these two specifications is the testing requirements. The Inconel bolt material … Continue reading
Posted in Application, FAQs, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged Difference between SAE AS7466 and SAE AS7467, Inconel bolts per AS7467, Inconel Bolts per SAE AS7467, Inconel per SAE AS7467, Inconel screws per AS7467, Inconel Screws per SAE AS7466, Inconel Screws per SAE AS7467, SAE AS7466 compared to SAE AS7467, SAE AS7466 Vs SAE AS7467 Leave a comment
Q: What is the corrosion (oxidation) resistance of 1.4980 (A-286) fasteners compared to 1.4404 (A4 / 316L ) fasteners? A: A286 / 1.4980 bolts provide excellent oxidation resistance up to 1500°F (815°C). This makes 1.4980 bolts ideal for high temperature exhaust streams. In comparison, 316L / 1.4404 bolts can typically be applied up … Continue reading
Posted in Application, FAQs, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged 1.4980 bolts, 1.4980 bolts for high temperature strength, 1.4980 bolts for oxidation resistance, 1.4980 fasteners, 1.4980 for high temperature strength, 1.4980 screws, 1.4980 screws for high temperature strength, 1.4980 screws for oxidation resistance Leave a comment
Q: What is the difference between screws made to ASTM A1014 and SAE AS7467? A: When it comes to the material characteristics there is not much difference in these specifications. Both standards describe bolts and screws made from Inconel 718 (UNS N07718) material equivalent to the European 2.4668 material norm. These both … Continue reading
Posted in Application, FAQs, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged Alloy 718 Bolts per ASTM A1014, Alloy 718 bolts per SAE AS7467, Alloy 718 screws per ASTM A1014, Alloy 718 screws per SAE AS7467, ASTM A1014 bolts, ASTM A1014 Compared to SAE AS7467, ASTM A1014 Screws, ASTM A1014 verses SAE AS7467, ASTM A1014 vs SAE AS7467, Inconel 718 Bolts per ASTM A1014, Inconel 718 per ASTM A1014, Inconel 718 per SAE AS7467 screws, Inconel 718 screw per SAE AS7467, Inconel 718 screws per ASTM A1014, Inconel bolts per SAE AS7467 screws, Inconel per ASTM A1014, Inconel per SAE AS7467, Inconel screws per SAE AS7467 screws, SAE AS7467 bolts, SAE AS7467 screws, What is the difference between ASTM A1014 and SAE AS7467 Leave a comment
Also known as Alloy 660, A286 bolts are a cost-effective material for high temperature strength – see why in this snapshot newsletter. What specifications can you offer? A286 is available in ASTM and many AMS standards (often required for aerospace applications) including: ASTM A453, AMS 5525, AMS 5726, AMS 5732, AMS 5737, AMS 5804. What … Continue reading
Posted in Application, Blog, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners Tagged A286 aerospace bolts, A286 aerospace fasteners, A286 aerospace screws, A286 AMS bolts, A286 AMS fasteners, A286 AMS screws, A286 bolts for high temperature, A286 NAS bolts, A286 NAS fasteners, A286 NAS screw, A286 screws for high temperature, AMS 5525 bolts, AMS 5525 screws, AMS 5726 bolts, AMS 5726 screws, AMS 5732 bolts, AMS 5732 screws, AMS 5737 bolts, AMS 5737 screws, AMS bolts A286, AMS screws A285, ASTM A453 bolts, ASTM A453 screws Leave a comment
Q: Is Monel stronger than stainless steel? A: In terms of strength, there are many grades of steel and stainless steel. Some of them are even cold-worked for added strength. So to compare Monel to “steel” would be a very broad question – and difficult to answer without knowing the … Continue reading
Posted in Application, FAQs, High Strength, Material, Specialty Metal Fasteners, Technical Questions Tagged Are monel bolts stronger than 316, are monel screws stronger than 316, Are monel screws stronger than stainless steel, Is monel stronger than stainless steel, Monel strength compared to 316, monel strength compared to stainless steel, Strength of Monel bolts compared to stainless steel, Strength of Monel compared to stainless steel, Strength of Monel screws compared to stainless steel, which are stronger monel bolts or 316 bolts, Which are stronger monel bolts or stainless steel bolts, which are stronger monel screws or 316 screws, which are stronger monel screws or stainless steel screws, which is stronger 316 or monel, Which is stronger monel or 316, which is stronger monel or stainless steel, which is stronger stainless steel or monel Leave a comment
Q: Is Monel better than titanium? A: Monel bolts and Titanium bolts have both similarities and differences. Both materials offer excellent resistance to saltwater. The only difference would be that Titanium has a slight advantage in stagnant seawater which can cause some corrosion to Monel. Both are the top materials … Continue reading
Posted in Application, Corrosion Resistance, FAQs, High Strength, Material, Specialty Metal Fasteners, Technical Questions Tagged Are monel bolts better than titanium, are monel bolts more corrosion resistant than titanium, Are monel bolts stronger than titnaium, Are monel screws better than titanium, are monel screws more corrosion resistant than titanium, Are monel screws stronger than titanium, Are titanium bolts better than monel, Are titanium bolts stronger than monel, Are titanium screws better than monel, Are titanium screws stronger than monel, How do monel bolts compare to titanium, How do monel screws compare to titanium, How do titanium bolts compare to monel, How do titanium screws compare to monel, How does monel compare to titanium, How does titanium compare to monel, Is Monel better than titanium, Is monel more corrosion resistant than titanium, Is Monel stronger than titanium, Is titanium better than monel, Is titanium stronger than monel, Which is better monel or titanium, Which is better titanium or monel Leave a comment
Q: Is Monel better than stainless steel? A: Monel bolts will offer improved resistance to saltwater over stainless steel. As a nickel alloy, Monel will provide much better general corrosion resistance as well. Monel is also known for its unmatched resistance to hydrofluoric acid which will even corrode pure tantalum. … Continue reading
Posted in Application, Corrosion Resistance, FAQs, High Strength, Material, Specialty Metal Fasteners, Technical Questions Tagged are monel bolts better than 316, Are monel bolts better than stainless steel, Are monel bolts more corrosion resistant than 316, Are monel bolts more corrosion resistant than stainless steel, are monel bolts stronger than stainless steel, are monel screws better than 316, are monel screws better than stainless steel, Are monel screws more corrosion resistant than 316, Are monel screws more corrosion resistant than stainless steel, Are monel screws stronger than stainless steel, How do monel bolts compare to stainless steel, How do monel screws compare to stainless steel, How does monel compare to stainless steel, Is monel better than 316, Is monel better than stainless steel, Is monel more corrosion resistant than 316, Is monel more corrosion resistant than stainless steel, Is monel stronger than 316, Is monel stronger than stainless steel, Monel bolts compared to stainless steal, Monel compared to stainless steel, monel screws compared to stainless steel Leave a comment
Q: I need a non-conductive screw. Can I use Carbon fiber reinforced PEEK? A: NO – The addition of carbon fibers into the polymer will significantly increase the conductivity of the material.
Nickel alloys are known for their corrosion resistance, but each material has its own special focus. This newsletter gives a quick summary of the top grades. Monel: Saltwater…And Strength For years, Monel bolts have been the go-to material for saltwater resistance by the military. … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners Tagged Difference between Hastelloy and Incone, Difference Between Hastelloy and Monel, Difference between Inconel and Hastelloy, Difference between Monel and Hastelloy, Difference between monel and Inconel, nickel alloys Leave a comment
Sulfuric Acid ( H2SO4 ) is one of the most widely used and important acids, being an essential component to many industries. Equally as important is selecting the right material to survive this environment. This newsletter will provide options. WHICH IS BEST? That depends on BOTH concentration and temperature – … Continue reading
Posted in Advanced Ceramic Fasteners, Blog, Corrosion Resistance, Engineered Polymer Fasteners, Material, Specialty Metal Fasteners, Uncategorized Tagged Alloy 20 bolts for H2so4 corrosion, Alloy 20 bolts for sulfuric acid corrosion, Alloy 20 for H2SO4 Corrosion, Alloy 20 for sulfuric acid Corrosion, Alloy 20 screws for H2SO4 Corrosion, alloy 20 screws for H2SO4 corrosion resistance, Alloy 20 screws for sulfuric acid corrosion, bolts for sulfuric acid corrosion, fasteners for H2SO4 Corrosion, Fasteners for Sulfuric Acid corrosion, H2SO4 corrosion, Hastelloy bolts for H2so4 corrosion, Hastelloy bolts for sulfuric acid corrosion, Hastelloy for H2SO4 Corrosion, Hastelloy for sulfuric acid Corrosion, Hastelloy screws for H2SO4 Corrosion, Hastelloy screws for sulfuric acid corrosion, Materials for sulfuric Acid corrosion, screws for h2so4 corrosion, screws for sulfuric acid corrosion, Sulfuric Acid Corrosion, Tantalum bolts for H2so4 corrosion, Tantalum bolts for sulfuric acid corrosion, Tantalum for H2SO4 Corrosion, Tantalum for sulfuric acid Corrosion, Tantalum screws for H2SO4 Corrosion, Tantalum screws for sulfuric acid corrosion, Zirconium bolts for H2SO4 Corrosion, Zirconium bolts for sulfuric acid Corrosion, Zirconium for H2SO4 Corrosion, Zirconium for sulfuric acid Corrosion, Zirconium screws for H2SO4 Corrosion, Zirconium screws for sulfuric acid Corrosion Leave a comment
Q: Am I right in understanding that polymer fasteners are chemically resistant? I know they are not nearly as strong or temperature resistant as a metal, but our temperatures are ambient so would this work for me? A: For HCl, you would want to consider PVDF polymer fasteners. These are … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Material, Technical Questions Tagged PVDF bolts for HCl, PVDF bolts for hydrochloric acid, PVDF fasteners for corrosion resistance, PVDF fasteners for HCl, PVDF fasteners for hydrochloric acid, PVDF for HCl, PVDF for hydrochloric acid, PVDF for hydrochloric acid corrosion, PVDF screws for corrosion resistance, PVDF screws for HCl, PVDF screws for hydrochloric acid Leave a comment
Polymers at Cryogenic Temperatures Most often people want to know how hot a material can be used up to in an application, however for cryogenic applications, in media like liquified gasses (nitrogen, oxygen, carbon dioxide, LNG, etc.), we need to understand how materials perform at very cold temperatures. Polymer fasteners … Continue reading
Posted in Application, Blog, Engineered Polymer Fasteners, High Strength, High Temperature Resistance, Material Tagged peek bolts for cryogenic, PEEK bolts for sub zero temperatures, Peek for cryogenics, Peek for sub-zero temperatures, Peek for sub-zero temps, PEEK screws for sub zero temperatures, polymer bolts for cryogenic, polymer bolts for sub zero temps, polymer bolts for subzero temps, polymer fasteners for cryogenic, polymer fasteners for sub zero temps, polymer fasteners for subzero temps, polymer screws for cryogenic, polymer screws for sub zero temps, polymer screws for subzero temps, Polymers for cryogenics, polymers for sub-zero temperatures, polymers for sub-zero temps, polymers for subzero temperatures, polymers for subzero temps, ptfe bolts for cryogenic, PTFE bolts for sub zero temperatures, PTFE for cryogenic, PTFE for sub-zero temps, PTFE for subzero temperatures, PTFE screws for sub zero temperatures, PVDF bolts for cryogenic, PVDF bolts for sub zero temperatures, PVDF for cryogenics, PVDF for sub-zero temps, PVDF for subzero temperatures, PVDF screws for sub zero temperatures Leave a comment
Q: Which polymer do we offer that would have the smallest compressibility and minimal thermal expansion? We have a very precise laser application. So if the screw changes its dimensions with increasing / decreasing temperatures or loads their device may not be as accurate as it should be. Can you … Continue reading
Q: We require materials with low outgassing (conforming to ASTM-E595) for use in a satellite and I have yet to find a polymer screw that could meet these requirements. Any ideas? A: I checked PEEK in NASA’s material out-gassing database. It looks like it will most likely meet the 1% … Continue reading
316 stainless is a familiar alloy to many of us and perhaps one of the most widely used fastening materials. Though it serves a critical function for industry, 316 can often fall short in servicing challenging high strength, temperature and corrosion resistant applications. Here is how it measures up in … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners Tagged 316 bolts compared to 17-4PH bolts, 316 bolts compared to AL6XN bolts, 316 bolts compared to duplex steel bolts, 316 bolts vs 17-4PH bolts, 316 bolts vs AL6XN bolts, 316 bolts vs alloy 20 bolts, 316 bolts vs duplex steel bolts, 316 compared to 17-4PH, 316 compared to AL6XN, 316 compared to duplex steel, 316 screws compared to 17-4PH screws, 316 screws compared to AL6XN screws, 316 screws compared to duplex steel screws, 316 screws vs 17-4PH screws, 316 screws vs AL6XN screws, 316 screws vs alloy 20 screws, 316 screws vs duplex steel screws, 316 stainless bolts compared to 17-4PH bolts, 316 stainless bolts compared to 310 stainless bolts, 316 stainless bolts compared to AL6XN bolts, 316 stainless bolts compared to alloy 20 bolts, 316 stainless bolts compared to duplex steel bolts, 316 stainless bolts vs 17-4PH bolts, 316 stainless bolts vs 310 stainless bolts, 316 stainless bolts vs AL6XN bolts, 316 stainless bolts vs alloy 20 bolts, 316 stainless compared to 17-4PH, 316 stainless compared to 310 stainless, 316 stainless compared to AL6XN, 316 stainless compared to alloy 20, 316 stainless compared to duplex steel, 316 stainless screws compared to 17-4PH screws, 316 stainless screws compared to 310 stainless screws, 316 stainless screws compared to AL6XN screws, 316 stainless screws compared to alloy 20 screws, 316 stainless screws compared to duplex steel screws, 316 stainless screws vs 17-4PH screws, 316 stainless screws vs 310 stainless screws, 316 stainless screws vs AL6XN screws, 316 stainless screws vs alloy 20 screws, 316 stainless steel bolts compared to 17-4PH bolts, 316 stainless steel bolts compared to 310 stainless steel bolts, 316 stainless steel bolts compared to AL6XN bolts, 316 stainless steel bolts compared to alloy 20 bolts0, 316 stainless steel bolts compared to duplex steel bolts, 316 stainless steel bolts vs 17-4PH bolts, 316 stainless steel bolts vs 310 stainless steel bolts, 316 stainless steel bolts vs AL6XN bolts, 316 stainless steel bolts vs alloy 20 bolts, 316 stainless steel compared to 17-4PH, 316 stainless steel compared to 310 stainless steel, 316 stainless steel compared to AL6XN, 316 stainless steel compared to alloy 20, 316 stainless steel compared to duplex steel, 316 stainless steel screws compared to 17-4PH screws, 316 stainless steel screws compared to 310 stainless steel screws, 316 stainless steel screws compared to AL6XN screws, 316 stainless steel screws compared to alloy 20 screws, 316 stainless steel screws compared to duplex steel screws, 316 stainless steel screws vs 17-4PH screws, 316 stainless steel screws vs 310 stainless steel screws, 316 stainless steel screws vs AL6XN screws, 316 stainless steel screws vs alloy 20 screws, 316 stainless steel vs 17-4PH, 316 stainless steel vs 310 stainless steel, 316 stainless steel vs AL6XN, 316 stainless steel vs alloy 20, 316 stainless vs 17-4PH, 316 stainless vs 310 stainless, 316 stainless vs AL6XN, 316 stainless vs alloy 20, 316 vs 17-4PH, 316 vs AL6XN, 316 vs alloy 20, 316 vs duplex steel Leave a comment
Q: I’m looking for polymer that can withstand around 400F for a high temperature sterilization process in a pharmaceutical application. In addition, I also need the polymer to meet FDA and USDA purity standards. Is this possible with Torlon screws. A: Torlon screws are a good high temperature polymer that … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions, Ultra Purity Tagged PEEK bolts for high purity, PEEK fasteners for high purity, PEEK FDA approved bolts, PEEK FDA approved fasteners, PEEK FDA approved screws, peek high purity bolts, peek high purity fasteners, PEEK high purity screws, PEEK screws for high purity, PEEK USDA approved bolts, PEEK USDA approved fasteners, PEEK USDA approved screws, Torlon bolts for high temperatures, Torlon screws for high temperatures Leave a comment
Q: I’m currently cruising the internet looking for the best way to support a ceiling via suspension from structural steel. We’re building a freezer, and I don’t want thermal bridging from the inside of the freezer up to the structural steel, so a metal rod is pretty much out of … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Strength, Material, Non-Conductive, Technical Questions Tagged glass fiber PEEK bolts for high strength, glass fiber PEEK bolts for high strength low thermal conductivity, glass fiber PEEK bolts for low thermal conductivity, glass fiber PEEK fasteners for high strength, glass fiber PEEK fasteners for high strength low thermal conductivity, glass fiber PEEK fasteners for low thermal conductivity, glass fiber PEEK for high strength, glass fiber PEEK screws for high strength, glass fiber PEEK screws for high strength low thermal conductivity, glass fiber PEEK screws for low thermal conductivity, PEEK bolts, PEEK bolts for high strength, PEEK Fasteners, PEEK fasteners for high strength, PEEK for high strength, PEEK Screws, PEEK screws for high strength Leave a comment
Inconel bolts are a nickel alloy fastener that are known for their use in high temperature applications that also require high strength. Many grades are also used for their excellent level of corrosion resistance in harsh chemical environments. This brief newsletter highlights the unique attributes of each Inconel bolt … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners Tagged choicing an inconel grade, Comparing Inconel grades, Comparison of Inconel bolts, Comparison of Inconel grades, Comparison of inconel screws, Inconel 600 bolts, Inconel 600 compared to 601, Inconel 600 compared to 625, Inconel 600 compared to Inconel 601, Inconel 600 compared to Inconel 625, Inconel 600 screws, Inconel 600 vs 601, Inconel 600 vs 625, Inconel 601 bolts, Inconel 601 compared to 625, Inconel 601 screws, Inconel 601 vs 625, Inconel 601 vs Inconel 625, Inconel 625 bolts, Inconel 625 screws, Inconel 718 bolts, Inconel 718 screws, Inconel bolt grades, Inconel Bolts, Inconel screw grades, Inconel Screws, Which inconel grade is best, Which inconel grade should I use, Which inconel is best Leave a comment
Q: We are attaching steel to aluminum in a drainage pond application, and need to prevent electrolysis. The aluminum materials are degrading prematurely. Is there a non-conductive bolt that would work for this situation? A: Your best bet is if you can use a polymer bolt like PEEK. PEEK bolts … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, Material, Non-Conductive, Technical Questions Tagged Non-conductive polymer bolt, Non-conductive polymer bolts, Non-conductive polymer screw, Non-conductive polymer screws, PEEK bolt for non-conductivity, PEEK bolts for non-conductivity, PEEK for galvanic corrosion prevention, PEEK screw for non-conductivity, PEEK screws for non-conductivity Leave a comment
Q: I have a customer asking me for 17-4PH stainless, but says they need it heat treated to H1100. What does this mean? A: 17-4PH bolts are available in many different heat treatment options. This means that different heat treatments such as H1150, H1100, H1075, etc are applied to the … Continue reading
Posted in Application, FAQs, High Strength, Specialty Metal Fasteners, Technical Questions Tagged 17-4PH Bolt Heat Treatment, 17-4PH Bolts Heat Treatment, 17-4PH Screw Heat Treatment, 17-4PH screws Heat Treatment, H1075 Heat treatment for 17-4PH bolt, H1075 Heat treatment for 17-4PH bolts, H1075 Heat treatment for 17-4PH screw, H1075 Heat treatment for 17-4PH screws, H1100 Heat treatment for 17-4PH Bolt, H1100 Heat treatment for 17-4PH Bolts, H1100 Heat treatment for 17-4PH screw, H1100 Heat treatment for 17-4PH screws, H1150 Heat treatment for 17-4PH bolt, H1150 Heat treatment for 17-4PH bolts, H1150 Heat treatment for 17-4PH screw, H1150 Heat treatment for 17-4PH screws, H900 Heat treatment for 17-4PH bolt, H900 Heat treatment for 17-4PH bolts, H900 Heat treatment for 17-4PH screw, H900 Heat treatment for 17-4PH screws, Heat treatments for 17-4PH Bolt, Heat treatments for 17-4PH Bolts, Heat treatments for 17-4PH Screw, Heat treatments for 17-4PH Screws Leave a comment
Q: I’m looking for a polymer fastener that can withstand ultraviolet radiation, but is also FDA approved as this is for a pharmaceutical application. Temperatures are around 100C. A: For this application, a good choice would be PVDF fasteners. PVDF screws are both FDA approved and are ideal for handling … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions, Ultra Purity Tagged PVDF bolt for ultraviolet radiation, PVDF bolts for ultraviolet radiation, PVDF screw for ultraviolet radiation, PVDF screws for ultraviolet radiation Leave a comment
Q: I’m working on a project that is using Titanium bolts for our equipment and we are considering a few different sizes and grade bolts; we are considering Gr.2, Gr.5, Gr.7 and Gr.12. What would you typically specify as the maximum tensile allowable (i.e. 2/3*yield) and the maximum shear allowable … Continue reading
Posted in Application, Corrosion Resistance, FAQs, High Strength, Material, Specialty Metal Fasteners, Technical Questions Tagged 5, 7 and 12, Comparing titanium grade 2 and 5 bolts, Comparing titanium grade 2 and 5 fasteners, Comparing titanium grade 2 and 5 screw, Comparing titanium grade 2 and 5 screws, Comparing titanium grades 2, Difference between titanium grades, Most corrosion resistant grade of titnaium, most corrosion resistant titanium, most economic titanium, Most economical grade of titanium, Strongest grade fo titnaium, strongest titanium Leave a comment
Q: I have a food processing application that requires a polymer screw that can get hot – about 300F. My concern is outgassing in the heat that can contaminate the food chemicals. Is there something that will not outgas that can work for me? A: For your application I would … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Technical Questions, Ultra Purity Tagged Bolt approved by FDA, Bolt approved by USDA, Bolts approved by FDA, Bolts approved by USDA, PEEK bolt 3A Dairy approved, PEEK bolt FDA approved, PEEK bolt for food applications, PEEK bolt USDA approved, PEEK bolts 3A Dairy approved, PEEK bolts FDA approved, PEEK bolts for food applications, PEEK bolts USDA approved, PEEK screw 3A Dairy approved, PEEK screw FDA approved, PEEK screw for food applications, PEEK screw USDA approved, PEEK screws 3A Dairy approved, PEEK Screws FDA approved, PEEK screws for food applications, PEEK screws USDA approved, Screw approved by FDA, Screw approved by USDA, Screws approved by FDA Leave a comment
Non-magnetic fasteners service a variety of applications mainly where magnetic “interference” needs to be avoided. Cryogenic and medical applications such as MRI’s are just a few of the key places non-magnetic fasteners are needed. This newsletter highlights a few specialty metal fasteners that can service non-magnetic needs. Inconel Bolts Non-magnetic … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, High Temperature Resistance, Lightweight, Material, Specialty Metal Fasteners Tagged non-magnetic aluminum bolt, non-magnetic aluminum bolts, non-magnetic aluminum screw, non-magnetic aluminum screws, non-magnetic bolt, non-magnetic bolts, non-magnetic Inconel bolt, non-magnetic Inconel bolts, non-magnetic Inconel screw, non-magnetic Inconel screws, non-magnetic metal bolt, non-magnetic metal bolts, non-magnetic metal screw, non-magnetic metal screws, non-magnetic screw, non-magnetic screws, non-magnetic titanium bolt, non-magnetic titanium bolts, non-magnetic titanium screw, non-magnetic titanium screws Leave a comment
Fasteners threads are made by one of two processes. Rolling the threads of the bolt or cutting them. This newsletter will describe each process, as well as the advantages and disadvantages. Rolled Threads This type of thread is made by a forming process where threads are created as the fastener … Continue reading
Posted in Application, Blog, Material, Specialty Metal Fasteners Tagged Bolt Cut Threads, Bolt Rolled Threads, Bolts Cut Threads, Bolts Rolled Threads, Cut Thread Bolt, Cut Thread Bolts, Cut Thread Fastener, Cut thread Fasteners, Cut Thread Screw, Cut Thread Screws, Cut Threads, Rolled Thread Bolt, Rolled Thread Bolts, Rolled Thread Fastener, Rolled Thread Fasteners, Rolled Thread Screw, Rolled Thread Screws, Rolled Threads, Screw Cut Threads, Screw Rolled Threads, Screws Cut Threads, Screws Rolled Threads Leave a comment
Q: I’m looking for a high temperature, strong fastener. I noticed that Hastelloy C276 bolts can be used to 1500F where A286 screws can only be used to 1300F. Does that make Hastelloy a better choice? A: Typically not. Hastelloy screws are most often used for high temperature corrosion. For … Continue reading
Cryogenic service can be harsh on any equipment, but gaskets have their own specific challenges. Due to the expansion and contraction when temperatures fluctuate between room and cryogenic, gasket sealing mechanisms can be compromised. This newsletter provides answers to issues facing gaskets in cryogenic service. How do cryogenic temps affect … Continue reading
Q: I want to use A286 fasteners with our product (a force sensor). Will A286 gall with 6Al4V titanium or 15-5 stainless steel or 304 SS helicoils without lubrication. The customer will not allow lubricants. Thank you A: The biggest factor to galling is using similar material on each other. … Continue reading
Q) I have cryogenic liquid hydrogen and hydrogen gas in my process and having a really hard time controlling leaks from flanges. All the gaskets I have used don’t seem last very long before leaking and cannot be tightened any further. Do you have any suggestions for dealing with this … Continue reading
Q: I’m looking for a polymer insert locknut for a marine environment. Can you make any suggestions? A: In your marine lock nut application, the polymer you should consider for the locking mechanism would be PVDF (Kynar). PVDF polymer in combination with the lock nut would perform very well in … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, Material, Non-Conductive, Technical Questions Tagged PVDF Insert Locknut for Marine Application, PVDF Insert Locknut for Salt Water, PVDF Insert Locknut for Saltwater, PVDF Insert Locknut for Sea water, PVDF Insert Locknut for Seawater, PVDF Lock Nut for Marine Application Leave a comment
Q: I cannot obtain an adequate seal with my existing metallic gaskets because my current flange and fastener maximum yield strengths will be exceeded. Any suggestions? A: JP/JG gaskets, with their unique design, offer and low tightening requirement across the surface of the gasket face in order to obtain extremely … Continue reading
Q: Can you suggest a gasket that reduces piping costs and how? A: For high temperature and pressure piping systems, the required clamping pressure or Seating Stress ‘Gb’ of the gasket in order to contain the process media’s measure of Tightness ‘Tp’ at specified levels of process pressure, is dictated … Continue reading
Posted in Application, FAQs, Material, Technical Questions Leave a comment
Q: I need a polymer flange that for a sterilization process. It would need to withstand temps of about 300F. Any suggestions? A: For this situation I would suggest a PEEK flange. PEEK is strong to temps of about 500F and performs excellently in both high temperature steam and water … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions Tagged PEEK flange for high temperature, PEEK Flange for high temperature sterilization, PEEK flange for radiation sterilization, PEEK Flange for steam sterilization, PEEK flange for sterilization Process, PEEK flanges for 300F Leave a comment
Q: What is the Vario gasket design? A: Vario is not a unique gasket at all, it is an adder to the existing JP/JG Revoseal gaskets to add in centering the gasket no matter what pressure class flange that the gasket is being mated to. This save metal costs as … Continue reading
Q: How do the Revoseal gaskets compare in terms of leak rate to a spiral wound or kammprofile style? A: The Revoseal gaskets perform hundreds to thousands of times better than these types of gaskets. Kammprofile gaskets leak 765 times MORE than a Revoseal gasket and spiral wound gaskets leak … Continue reading
Posted in Application, FAQs, Material, Specialty Metal Fasteners, Technical Questions Tagged better leak rate than kammprofile, better leak rate than spiral wound gasket, gasket with better leak rate than camprofile, gasket with better leak rate than kammprofile, gasket with better leak rate than spiral wound gasket, gasket with lower leak rate than camprofile, gasket with lower leak rate than kammprofile, gasket with lower leak rate than spiral wound gasket, lower leak rate gasket than camprofile, lower leak rate gasket than kammprofile, lower leak rate gasket than spiral wound gasket, Revoseal gasket vs kammprofile gasket, Revoseal gasket vs spiral wound gasket Leave a comment
Q: I need a high temperature gasket that can provide a tight seal to a hazardous application that reaches temps of about 1200F. Do you have a product that can help me? A: Yes. An Inconel JG / JP gasket can give you high temperature resistance at these temperatures. The … Continue reading
Posted in Application, FAQs, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged High temperature gasket, high temperature proof gasket, high temperature resistant gasket, leak proof gasket, leak proof seal gasket, leak resistant gasket, temperature resistant gasket Leave a comment
Q: I need a gasket for dissimilar flange faces with an 8mm gap. Is there a solution you can provide to fit this issue? A: Yes. We can produce custom JG / JP gaskets that fit dissimilar flange faces for a tight seal. JG / JP gaskets could be made … Continue reading
Q: I’m using a spiral wound gasket and am having difficulties with leakage. Can you recommend something that can protect against leakage and handle a harsh salt-rich corrosive environment? A: For this type of application I would recommend a titanium or Titanium JG / JP gasket. This style of gasket … Continue reading
Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners, Technical Questions Tagged chloride corrosion resistant gasket, corrosion resistant gasket, Gasket better than spiral wound, leak proof gasket, leak resistant gasket, low leak rate gasket, Lowest Leak Rate Gasket, salt corrosion resistant gasket, titanium corrosion resistant gasket, titanium gasket, titanium gasket better than spiral wound, Titanium JG / JP Gasket, Titanium leak proof gasket Leave a comment
Q: I have a leaking gasket that is in a heat transfer fluid application. What do you recommend? A: For this situation you may want to try the Revolution gasket system. Due to consistent sealing pressure it will offer you a far lower leak rate than an off the shelf … Continue reading
Posted in Application, FAQs, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged consistent sealing gasket, gasket for fluid transfer application, gasket for heat transfer fluid aplication, high sealing gasket, low leak rate gasket, Low Leak rate gasket for heat transfer fluid application, revolution gasket system, Revoseal gasket system, revoseal revolution gasket, Vibration proof gasket Leave a comment
Q: We are looking for a non-conductive screw that gets close to the strength of 316 stainless steel, ideas? A: The best we could offer would be our glass fiber reinforced PEEK screws. It has nearly double the tensile strength as natural PEEK at about 22,800 psi. You could also … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Engineered Polymer Fasteners, FAQs, High Strength, Technical Questions Tagged Glass Fiber Peek bolts electrical insulation, Glass Fiber Peek bolts for non-conductive application, Glass Fiber Peek fasteners electrical insulation, Glass Fiber Peek fasteners for non-conductive application, Glass Fiber Peek screws electrical insulation, Glass Fiber Peek screws for non-conductive application, PEEK bolts for high strength, PEEK fasteners for high strength, PEEK screws for high strength Leave a comment
Q: I’m looking for threaded rods and nuts that would need to be able to withstand a potential exposure to ferric chloride and constant exposure to 3% hydrochloric acid which could reach 31% in a rare instance, would this PEEK withstand these chemicals? A: PEEK fasteners work well with harsh … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Technical Questions Tagged PEEK fasteners for hydrochloric acid, PEEK fasteners for hydrochloric acid corrosion resistance, PEEK for hydrochloric acid, PEEK for hydrochloric acid corrosion resistance, PEEK screws for hydrochloric acid, PEEK threaded rod for hydrochloric acid, polymer fasteners for hydrochloric acid, Polymers for hydrochloric acid Leave a comment
Q: I have a high pressure steam application that is affected by a lot of hammering (pressure fluctuations). What gasket design can I use to prevent leakage? A: For this application I would recommend the Revoseal Eco+. Not only does this gasket offer 1000x better sealing than graphite gaskets, its … Continue reading
Posted in Application, FAQs, Material, Specialty Metal Fasteners, Technical Questions Tagged Gasket better than camprofile gasket, Gasket better than graphite gasket, Gasket for high pressure steam application, Gasket for steam application, Gaskets better than spiral wound gasket, gaskets for fluctuating pressure, Gaskets for hammering application, Gaskets for High Pressure, Gaskets for Pressure fluctuations, High Pressure Gasket, High Pressure Revoseal Gasket, Low leak gasket, low leak rate gasket, Revoseal Eco+ Gasket Leave a comment
Q: I need a high temperature gasket that would be able to handle thermal cycling. Any ideas? A: The Revolution gasket is ideal for thermal cycling. The design of the gasket accommodates flange movement that can be caused by thermal cycling and vibration. The corrugated design of the Revolution gasket … Continue reading
Posted in Application, FAQs, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions Tagged gasket for cyclic conditions, gasket for cyclic temperature conditions, gasket for high temperature, gasket for thermal cycling, High temperature gasket, low leak rate gasket, low leak rate gasket for cyclic conditions, low leak rate gasket for cyclic temperature, low leak rate high temperature gasket, low leak rate thermal cycling gasket, revolution gasket, revoseal revolution gasket Leave a comment
Q: I need a polymer fastener that offers the best corrosion resistance at high temperatures. I’m using a low percentage of H2SO4 but temps can get up to 300F. Any ideas? A: The best polymer fastener for high temperature corrosion resistance is PTFE screws. PTFE fasteners offer excellent corrosion resistance … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions Tagged PTFE bolts for H2SO4 corrosion, PTFE bolts for high temperature corrosion, PTFE bolts for sulfuric acid corrosion, PTFE fasteners for H2SO4 corrosion, PTFE fasteners for high temperature corrosion, PTFE fasteners for sulfuric acid corrosion, PTFE screws for H2SO4 corrosion, PTFE screws for high temperature corrosion, PTFE screws for sulfuric acid corrosion Leave a comment
Q: Do ceramic fasteners provide strength? A: The answer to your question is both yes and no. They provide decent tensile strength similar to some stainless steels(Aluminia bolts has a tensile strength of 30 ksi and Zirconia screws 75 ksi), however they don’t have any yield strength. Due to the … Continue reading
Posted in Advanced Ceramic Fasteners, Application, FAQs, High Strength, Material, Technical Questions Tagged strength of alumina bolts, strength of alumina fasteners, strength of alumina screws, strength of alunina ceramic bolts, strength of alunina ceramic fasteners, strength of alunina ceramic screws, strength of ceramic bolts, Strength of ceramic fasteners, strength of ceramic screws, strength of zirconia bolts, strength of zirconia ceramic bolts, strength of zirconia ceramic fasteners, strength of zirconia ceramic screws, strength of zirconia fasteners, strength of zirconia screws Leave a comment
Q: I need a polymer fastener that can withstand high temp pharma sterilization processes? There may also be chemical contaminants in the process. A: Depending on the temperatures you are looking at, the three options to consider would be PEEK, PVDF or PTFE fasteners. PEEK fasteners can be used to … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions, Ultra Purity Tagged PEEK bolts for sterilization processes, PEEK fasteners for sterilization processes, PEEK screws for sterilization processes, PTFE bolts for sterilization processes, PTFE fasteners for sterilization processes, PTFE screws for sterilization processes, PVDF bolts for sterilization processes, PVDF fasteners for sterilization processes, PVDF screws for sterilization processes Leave a comment
Q: Looking for a bolt rated 320 psi for use at a temperature of 1292F on an Incoloy 80oHT flange? Suggestions? A: Assuming you want hex head bolts and Inconel 625 is probably your best choice at those temperatures. At about 1300F, Inconel 625 bolts (per the chart below) should … Continue reading
Q: I’m using PEEK fasteners in hydrochloric acid but am seeing a slight bit of corrosion or degradation of the fastener. Can you recommend a better polymer for resistance? A: For corrosion in HCL, a better choice may be PTFE screws. PTFE fasteners are virtually inert to most organics, acids … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Material, Technical Questions Tagged PTFE bolts for acid corrosion, PTFE bolts for corrosion, PTFE bolts for hydrochloric acid corrosion, PTFE fasteners for acid corrosion, PTFE fasteners for corrosion, PTFE fasteners for hydrochloric acid corrosion, PTFE screws for acid corrosion, PTFE screws for corrosion, PTFE screws for hydrochloric acid corrosion, PTFE vs PEEK bolts for corrosion, PTFE vs PEEK bolts for hydrochloric acid corrosion, PTFE vs PEEK fasteners for corrosion, PTFE vs PEEK fasteners for hydrochloric acid corrosion, PTFE vs PEEK screws for corrosion, PTFE vs PEEK screws for hydrochloric acid corrosion Leave a comment
Q: I have a high temperature sterilization process and am using PVDF screws. They seem to be weakening under the temperatures that approach 300F. Any suggestions? A: PEEK fasteners may be a good fit for your application. PEEK screws stay strong and retain their mechanical properties to about 500F. They … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions Tagged PEEK bolts for 300F, PEEK bolts for high temperature sterilization, PEEK bolts for sterilization, Peek fasteners for 300F, PEEK fasteners for high temperature sterilization, PEEK fasteners for sterilization, PEEK screws for 300F, PEEK screws for high temperature sterilization, PEEK screws for sterilization Leave a comment
Q: What would be the highest strength polymer fastener I can use to 400F? A: For this application, probably the best option for you would be PEEK fasteners. PEEK screws are usable to 500F and are available in three levels of strength. Unfilled natural PEEK fasteners offer 16,000 psi tensile … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Strength, High Temperature Resistance, Material, Technical Questions Tagged High STrength PEEK bolts, High strength PEEK Fasteners, High strength PEEK screws, PEEK bolts for strength, PEEK fasteners for strength, PEEK screws for strength Leave a comment
Duplex Steel: Strength & Corrosion Resistance Beyond 316 316 Stainless steel fasteners have many applications, but if you are looking for an all-around improved fastener without breaking the budget, Duplex alloys might be a good choice. Duplex steel fasteners are known for their improved strength (being about 2x stronger) and … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, Material, Specialty Metal Fasteners Tagged Duplex 2507 steel bolts vs 316 Stainless Steel, Duplex alloy bolts vs. 316 Stainless Steel, Duplex alloy fasteners vs. 316 Stainless Steel, Duplex alloy screws vs. 316 Stainless Steel, Duplex bolts vs. 316 Stainless Steel, Duplex fasteners vs. 316 Stainless Steel, Duplex screws vs. 316 Stainless Steel, Duplex steel bolts vs 316 Stainless Steel, Duplex steel fasteners vs 316 Stainless Steel, Duplex steel screws vs 316 Stainless Steel, Duplex steel vs 316 Stainless Steel, Duplex steel vs. 316 Stainless Stee, Super Duplex 2507 steel bolts vs 316 Stainless Steel, Super Duplex 2507 steel fasteners vs 316 Stainless Steel, Super Duplex 2507 steel screws vs 316 Stainless Steel Leave a comment
Q: What is the max temperature I could expose PEEK screws to HCl? A: This depends on the concentration of the HCl but if you were at about 15%, the PEEK fasteners can be exposed to about 100C of hydrochloric acid solution. See this chart https://www.extreme-bolt.com/peek-fasteners-flanges.html#Chemical. That is the max … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Strength, High Temperature Resistance, Technical Questions Tagged Exposing PEEK bolts to HCL, Exposing peek bolts to hydrochloric acid, Exposing Peek fasteners to HCl, Exposing PEEK fasteners to Hydrochloric acid, Exposing PEEK Screws to HCl, Exposing PEEK screws to hydrochloric acid, max temperature I could expose PEEK bolts to HCl, max temperature I could expose PEEK fasteners to HCl, max temperature I could expose PEEK fasteners to Hydrochloric acid, max temperature I could expose PEEK screws to HCl, max temperature I could expose PEEK screws to hydrochloric acid Leave a comment
Q: We are looking for high shear strength non-conductive flat head screws being used for electrical insulation. The screws need to have a high shear strength quality as other plastics screws we have tried have broken. Do you have a material you can recommend? A: With regards to a polymer … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Strength, Material, Non-Conductive, Technical Questions Tagged Glass Fiber Peek bolts electrical insulation, Glass Fiber Peek bolts for high strength insulation, Glass Fiber Peek fasteners electrical insulation, Glass Fiber Peek fasteners for high strength insulation, Glass Fiber Peek screws electrical insulation, Glass Fiber Peek screws for high strength insulation, Glass Fiber Reinforced Peek bolts electrical insulation, Glass Fiber Reinforced Peek bolts for high strength insulation, Glass Fiber Reinforced Peek fasteners electrical insulation, Glass Fiber Reinforced Peek fasteners for high strength insulation, Glass Fiber Reinforced Peek for high strength insulation, Glass Fiber Reinforced Peek screws electrical insulation, Glass Fiber Reinforced Peek screws for high strength insulation, Glass Reinforced Peek bolts for high strength insulation, Glass Reinforced Peek fasteners for high strength insulation, Glass Reinforced Peek for high strength insulation, Glass Reinforced Peek screws for high strength insulation Leave a comment
Q: I’m using Duplex 2205 for a saltwater application but am starting to have some corrosion due to some sulfuric acid contamination. Can you suggest anything that might help improve the corrosion resistance? A: If you’re on the borderline with Duplex 2205 you might want to consider a Super Duplex … Continue reading
Posted in Application, Corrosion Resistance Tagged zeron 100 bolts for acid corrosion, zeron 100 bolts for saltwater corrosion, zeron 100 fasteners for acid corrosion, zeron 100 fasteners for saltwater corrosion, zeron 100 screws for acid corrosion, zeron 100 screws for saltwater corrosion, Zeron Bolts for Saltwater and Acid corrosion, Zeron Fasteners for Saltwater and Acid corrosion, zeron screws for saltwater and acid corrosion Leave a comment
Q: I’m looking for a polymer that can be exposed to low concentration of sulfuric acid. Which polymer do you recommend? I tried PTFE but they don’t seem to be as strong as I need. A: PTFE and PFA fasteners offer the highest polymer corrosion resistance but the trade-off is … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Strength, Technical Questions Tagged polymer bolts for sulfuric acid, polymer fasteners for sulfuric acid, polymer screws for sulfuric acid, PVDF bolts for sulfuric acid, PVDF bolts for sulfuric acid corrosion resistance, PVDF fasteners for corrosion resistance, PVDF fasteners for sulfuric acid, PVDF fasteners for sulfuric acid corrosion resistance, PVDF screws for sulfuric acid, PVDF screws for sulfuric acid corrosion resistance Leave a comment
Q: I need a fastener that can withstand frequent sterilization processes at temps to around 400F. I would prefer a polymer if possible. Also the process is pharma related, so the screws would need to be non leaching and may be exposed to low concentrations of chemicals. Any ideas? A: … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions, Ultra Purity Tagged FDA approved bolts, FDA approved fasteners, FDA approved peek bolts, FDA approved PEEK fasteners, FDA approved PEEK screws, FDA approved screws, Hydrolysis resistant bolts, Hydrolysis resistant fasteners, Hydrolysis resistant PEEK bolts, Hydrolysis resistant PEEK fasteners, Hydrolysis resistant PEEK screws, Hydrolysis resistant screws, PEEK bolts FDA approved, PEEK bolts for Pharmaceutical purity, PEEK bolts for purity, PEEK bolts for sterilization processes, PEEK fasteners FDA approved, PEEK fasteners for Pharmaceutical purity, PEEK fasteners for purity, PEEK fasteners for sterilization processes, PEEK Screws FDA approved, PEEK screws for Pharmaceutical purity, PEEK screws for purity, PEEK screws for sterilization processes Leave a comment
Q: Hello I am researching titanium and C276 hardware for a submerged application in a high chloride (20,000 mg/L) elevated temperature environment (125F). Corrosion resistance is more important than shear or tensile strength in this application. A: Titanium screws should be a good choice for your application especially Grade 2 … Continue reading
Posted in Application, Corrosion Resistance, FAQs, High Strength, Technical Questions Tagged Hastelloy bolts for chloride and HCL corrosion, Hastelloy C276 bolts for chloride and HCL corrosion, Hastelloy C276 fasteners for chloride and HCL corrosion, Hastelloy C276 screws for chloride and HCL corrosion, Hastelloy fasteners for chloride and HCL corrosion, Hastelloy screws for chloride and HCL corrosion, Titanium bolts for chloride corrosion, Titanium fasteners for chloride corrosion, Titanium grade 2 bolts for chloride corrosion, Titanium grade 2 fasteners for chloride corrosion, Titanium grade 2 screws for chloride corrosion, Titanium screws for chloride corrosion Leave a comment
Q: Will Nickel 200 bolts be a good choice for hydrofluoric acid? A: For aqueous HF, Nickel 200 fasteners offer limited protection. If application requires a metal then you may want to consider Monel 400. Monel 400 bolts are the most resistant option for hydrofluoric acid in all concentrations up … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Material, Specialty Metal Fasteners, Technical Questions Tagged Monel 400 bolts for HF corrosion, Monel 400 bolts for hydrofluoric acid corrosion, Monel 400 fasteners for HF corrosion, Monel 400 fasteners for hydrofluoric acid corrosion, Monel 400 for hydrofluoric acid corrosion, Monel 400 screws for hydrofluoric acid corrosion, PTFE bolts for HF corrosion, PTFE bolts for hydrofluoric acid corrosion, PTFE fasteners for HF corrosion, PTFE fasteners for hydrofluoric acid corrosion, PTFE screws for HF corrosion, PTFE screws for hydrofluoric acid corrosion, PVDF bolts for HF corrosion, pvdf bolts for hydrofluoric acid corrosion, PVDF fasteners for HF corrosion, pvdf fasteners for hydrofluoric acid corrosion, PVDF screws for HF corrosion, pvdf screws for hydrofluoric acid corrosion Leave a comment
Q: I am looking for recommendations for fasteners capable of operating under load at 2000C, in a mild vacuum environment. The material can be conductive or insulating just along as it does not react with carbon. A: For temperatures as high as 2000C, Zirconia ceramic fasteners would be your only … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Corrosion Resistance, FAQs, High Temperature Resistance, Technical Questions Tagged zirconia bolts for high temperature, zirconia ceramic bolts for 2000C application, zirconia ceramic bolts for high temperature, zirconia ceramic fasteners for 2000C application, zirconia ceramic fasteners for high temperature, zirconia ceramic screws for 2000C application, zirconia ceramic screws for high temperature, zirconia fasteners for 2000C application, zirconia fasteners for high temperature, zirconia screws for 2000C application, zirconia screws for high temperature Leave a comment
Q: I have an application with high temperature exhaust that requires a high strength bolt for oxidation resistance. Temps are pretty consistent around 1300F. Would Inconel 718 bolts be a good choice? A: Inconel 718 would definitely be one good option. Inconel 718 bolts offer 210ksi tensile strength and are … Continue reading
Posted in Application, FAQs, High Strength, High Temperature Resistance, Technical Questions Tagged A286 bolts for high temperatures, A286 fasteners for high temperatures, A286 screws for high temperatures, Alloy 718 bolts for high temperatures, Alloy 718 fasteners for high temperatures, Alloy 718 screws for high temperatures, Inconel 718 bolts for high temperatures, Inconel 718 fasteners for high temperatures, Inconel 718 screws for high temperatures, Nimonic 80A bolts for high temperatures, Nimonic 80A fasteners for high temperatures, Nimonic 80A screws for high temperatures, Nimonic bolts for extreme temperatures, Nimonic bolts for high temperatures, Nimonic fasteners for extreme temperatures, Nimonic fasteners for high temperatures, Nimonic screws for extreme temperatures, Nimonic screws for high temperatures Leave a comment
Q: I am needing to replace some hex heads and nuts on an HCL tank lid. It appears they were originally coated and due to a previous leak, they are starting to corrode. What would be the best alternative bolt type for this situation? HCL concentration is 37% and is … Continue reading
Posted in Application, Corrosion Resistance, FAQs, Material, Technical Questions Tagged Hastelloy bolts for HCl corrosion, Hastelloy bolts for hydrochloric acid corrosion, Hastelloy C276 bolts for HCl corrosion, Hastelloy C276 fasteners for HCl corrosion, Hastelloy C276 screws for HCl corrosion, Hastelloy FAsteners for HCl corrosion, hastelloy fasteners for hydrochloric acid corrosion, hastelloy screws for HCl corrosion, hastelloy screws for hydrochloric acid corrosion Leave a comment
Q: We are looking for a non-conductive screw with lower dielectric constant / dissipation factor to replace a steel screw (Tensile Strength 70kpsi) in one of our products. So were trying to get to similar strength / properties to the steel screw to meet our torque requirements. Will a ceramic … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Engineered Polymer Fasteners, FAQs, Non-Conductive, Technical Questions Tagged alumina screws for Low Dielectric Constant, ceramic screws for Low Dielectric Constant, PEEK bolts for Low Dielectric Constant, PEEK fasteners for Low Dielectric Constant, PEEK glass filled bolts for Low Dielectric Constant, PEEK glass filled fasteners for Low Dielectric Constant, PEEK glass filled screws for Low Dielectric Constant, PEEK screws for Low Dielectric Constant, zirconia screws for Low Dielectric Constant Leave a comment
Q: I need a material that is resistant to a small concentration of hydrofluoric acid at room temperature? Can you offer any suggestions? A: Two materials come to mind. First in terms of metal alloys Monel 400 bolts are resistant to most concentrations of hydrofluoric acid. If you prefer a … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Material, Technical Questions Tagged Monel 400 bolts for hydrofluoric acid corrosion, Monel 400 fasteners for hydrofluoric acid corrosion, Monel 400 screws for hydrofluoric acid corrosion, Monel bolts for hydrofluoric acid corrosion, Monel fasteners for hydrofluoric acid corrosion, Monel screws for hydrofluoric acid corrosion, PTFE bolts for hydrofluoric acid corrosion, PTFE fasteners for hydrofluoric acid corrosion, PTFE screws for hydrofluoric acid corrosion Leave a comment
Q: We are having some issues with corrosion in a highly sensitive pharma application. I need a bolt that is corrosion resistant to both acids and organics, but is usable in a high purity situation. Temperatures can reach about 120F. Also, it would need to be a polymer screw available … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Technical Questions, Ultra Purity Tagged polymer fasteners for FDA application, polymer fasteners for pharmaceutical, polymer screws for corrosion, polymer screws for FDA, polymer screws for pharmaceutical, polymer screws for USDA application, PTFE fasteners for corrosion, PTFE fasteners for FDA application, PTFE fasteners for USDA application, PTFE screws for corrosion, PTFE screws for FDA application, ptfe screws for USDA application, PVDF fasteners for corrosion, PVDF fasteners for FDA, PVDF fasteners for high purity, PVDF for high purity, PVDF screws for corrosion, pvdf screws for FDA, PVDF screws for high purity, pvdf screws for USDA application Leave a comment
Q: How do ceramic alumina screws compare to steel screws as far as strength goes? The load would most likely be tension, but some compression too. A: If you compare 316 Stainless Steel to Zirconia ceramic screws, their tensile strengths are similar (around 75 ksi tensile) with Alumina ceramics being … Continue reading
Posted in Advanced Ceramic Fasteners, Application, FAQs, High Strength, Technical Questions Tagged alumina ceramic screw strength, alumina screws compared to stainless steel, Ceramics screws compared to stainless steel, strength of alumina ceramic screws compared to stainless steel, strength of zironia ceramic screws compared to stainless steel, zirconia ceramic screw strength, zirconia screws compared to stainless steel Leave a comment
A. We need a screw that is usable at 200C in air only, so no chemical resistance needed. I like the high strength of the Carbon Fiber PEKK or PEEK Extreme. Will these work?A Q: Would recommend using either Glass filled PEEK or Vespel. Vespel screws are made from the … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Technical Questions Tagged glass filled peek for high temperatures, glass filled peek screws for high temperature strength, glass filled peek screws for strength, Polyimide fasteners for high temperature, Polyimide screws for high temperature, Vespel fasteners for high temperature, vespel screws for high temperature Leave a comment
Q: Looking to change to a non-conductive material for use in a high impact application. Would Alumina or Zirconia ceramic fasteners be a good fit? A: We could certainly quote you some ceramic hardware, however ceramics may not be the best non-conductive choice for a high impact environment. Ceramic fasteners … Continue reading
Posted in Application, FAQs, High Strength, Non-Conductive, Technical Questions Tagged non-conductive fasteners, non-conductive polymer fasteners, PEEK bolts for non-conductive applications, PEEK bolts for non-conductivity, PEEK fasteners for non-conductive applications, PEEK fasteners for non-conductivity, PEEK screws for non-conductive applications, PEEK screws for non-conductivity Leave a comment
Fasteners for CHLORIDE CORROSION Fighting chloride corrosion is one of the most common issues that face industrial processes. From industrial process in water treatment to pulp & paper as well as seawater applications, chlorides are very common and menace to industry. This brief newsletter shares insight into which materials for … Continue reading
Posted in Application, Blog, Corrosion Resistance Tagged AL6XN bolts for chloride corrosion, AL6XN fasteners for chloride corrosion, AL6XN screws for chloride corrosion, alloy 20 bolts for chloride corrosion, Alloy 20 fasteners for chloride corrosion, Alloy 20 screws for chloride corrosion, bolts for chloride corrosion, chloride corrosion, duplex steel bolts for chloride corrosion duplex steel screws for chloride corrosion, duplex steel for chloride corrosion duplex steel fasteners for chloride corrosion, fasteners for chloride corrosion, screws for chloride corrosion, Titanium bolts for chloride corrosion, Titanium fasteners for chloride corrosion, Titanium screws for chloride corrosion Leave a comment
Q: I have a need for a fastener for cyrogenic Helium (3.5K) application. Ideally, the fastener would be non conductive (electrically). Are any of the non conductive options you have listed good for cryo use? A: You might want to consider PTFE of PEEK fasteners. These are polymers that will … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, Material, Non-Conductive, Technical Questions Tagged cryogenic polymer fasteners, cryogenic polymer screws, cyrogenic polymer bolts, peek bolts for cryogenic, peek fasteners for cryogenic, peek screws for cyrogenic, ptfe bolts for cryogenic, ptfe fasteners for cryogenic, ptfe screws for cryogenic Leave a comment
Q: I see that you list 5 different grades of Tungsten on your site, would you maybe help me choose which is the best for my application? A: There are two important differences. First, pure tungsten screws are stronger. For example 99.95% tungsten offers 142 ksi UTS vs Class 1 … Continue reading
Posted in Application, FAQs, High Strength, Technical Questions Tagged difference between pure tungsten and alloyed tungsten, pure tungsten fasteners, pure tungsten screws, tungsten alloy fasteners, tungsten alloy screws, tungsten fasteners, tungsten fasteners for strength, tungsten screws, tungsten screws for strength Leave a comment
PEEK, PVDF and PTFE all offer lightweight, electrical & thermal insulation and great corrosion resistance. But when it comes to strength, temperature, purity and corrosion, each has its niche. The newsletter points out which is best to use in different conditions. TEMPERATURE PEEK and PTFE screws offer excellent high temperature … Continue reading
Posted in Application, Blog, Corrosion Resistance, Engineered Polymer Fasteners, High Strength, High Temperature Resistance, Lightweight, Material Tagged corrosion resistant polymer bolts, corrosion resistant polymer screws, high strength polymer bolts, High strength polymer fasteners, high strength polymer screws, high temperature polymer bolts, high temperature polymer screws, high temperature resistant polymer fasteners, high temperature resistant polymer scres, polymer bolts for corrosion, polymer bolts for high temperature, polymer fasteners for corrosion, polymer screws for corrosion, Polymer screws for high temperature Leave a comment
What is a refractory metal fastener? Molybdenum, tantalum, tungsten and zirconium are all refractory metals. (We are excluding titanium from this topic although it can be considered a refractory metal by certain definitions). All these refractory metal fasteners are characterized by their high-temperature melting points, but they also have other … Continue reading
Posted in Blog, High Temperature Resistance, Specialty Metal Fasteners Tagged Molybdenum bolts for high temperature, molybdenum refractory metal bolt, molybdenum refractory metal fastener, molybdenum refractory metal screw, molybdenum screws for high temperature, refractory metal bolts, Refractory Metal Fasteners, refractory metal screws, tantalum bolts for corrosion resistance, tantalum fasteners for corrosion resistance, tantalum fasteners for high temperature, tantalum screws for corrosion resistance, tungsten bolts for density, tungsten bolts for high temperature, tungsten fasteners for density, tungsten fasteners for high temperature, tungsten screws for density, tungsten screws for high temperature, zirconium bolts for corrosion, zirconium fasteners for corrosion, zirconium refractory metal bolts, zirconium refractory metal fasteners, zirconium refractory metal screws, zirconium screws for corrosion 3 Comments
Q: I need a bolt that can handle high temperatures and be an electric insulator? What can I use? A: That depends on what you mean by high temperature and what other issues you have like the strength requirements. If you are talking about temperatures under 500F, then you may … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Engineered Polymer Fasteners, FAQs, Non-Conductive, Technical Questions Tagged Alumina fastener electric insulation, Alumina fasteners for electric insulation, Alumina screw electric insulation, Alumina screws for electric insulation, Ceramic fastener electric insulation, Ceramic screw electric insulation, PEEK bolts for electric insulation, PEEK fastener electric insulation, PEEK fasteners for electric insulation, PEEK screw electric insulation, PEEK screws for electric insulation Leave a comment
Titanium is an amazing material offering strength, lightness of weight, and corrosion resistance but there are also instances that titanium should not be used. This brief newsletter covers the do’s and don’ts of titanium screws. Do Use for Saltwater & Chloride Resistance One of the most noteworthy uses of titanium … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, Lightweight, Specialty Metal Fasteners Tagged titanium bolts for chloride, Titanium bolts for chloride corrosion, titanium bolts for saltwater, titanium bolts for saltwater corrosion, titanium fastener applications, titanium fastener uses, titanium fasteners for chloride, Titanium fasteners for chloride corrosion, titanium fasteners for saltwater, titanium fasteners for saltwater corrosion, titanium screws for chloride, Titanium screws for chloride corrosion, titanium screws for saltwater, titanium screws for saltwater corrosion Leave a comment
Q: I’m looking for a socket head cap screw that is 5/8″-11 x 5.5 inches in length. Need the material to be non-conductive and was thinking Ceramic Zirconia? Would that work? A: Ceramics like Zirconia screws are in fact an excellent insulator from electrical current. However zirconia ceramic fasteners are … Continue reading
Posted in Advanced Ceramic Fasteners, Engineered Polymer Fasteners, FAQs, Non-Conductive, Technical Questions Tagged ceramic bolts for electric insulation, ceramic fasteners for electric insulation, ceramic screws for electric insulation, PEEK bolts for electric insulation, PEEK fasteners for electric insulation, PEEK fasteners for insulation, PEEK screws for electric insulation, PEEK screws for insulation, zirconia bolts for electric insulation, zirconia bolts for insulation, zirconia ceramic bolts for electric insulation, zirconia ceramic fasteners for electric insulation, zirconia ceramic screws for electric insulation, zirconia fasteners for electric insulation, zirconia fasteners for insulation, zirconia screws for electric insulation, zirconia screws for insulation Leave a comment
Q: I’m looking for a polymer washer that can be used as a dielectric break between aluminum and titanium. It will also be exposed to salt water. Is torlon a good choice? A: Torlon washers will work in this situation, but there are probably more cost efficient solution for this … Continue reading
Posted in Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Technical Questions Tagged PEEK fasteners for salt water resistance, PEEK fastners for dielectric strength, PEEK for salt water resistance, PEEK screws for dielectric strength, PEEK screws for salt water resistance, PEEK washers for dielectric strength, PEEK washers for salt water resistance, Torlon bolts for dielectric strength, Torlon fasteners for high temperature appliations, Torlon fastners for dielectric strength, Torlon screws for dielectric strength, Torlon screws for high temperature appliations, Torlon washers for dielectric strength, Torlon washers for high temperature appliations Leave a comment
Q: Since Monel is resistant to NaCl does that mean it can handle a strong chloride situation? A: Monel is resistant to chlorides but, for strong chlorides your best bet is to use Titanium screws. Titanium fasteners are almost inert to all chlorine and chloride environments due to the fact … Continue reading
Posted in Corrosion Resistance, FAQs, Material, Technical Questions Tagged titanium bolts and chloride corrosion, Titanium bolts chloride corrosion, Titanium bolts chlorine corrosion, Titanium bolts for chloride corrosion, Titanium bolts for chloride resistance, titanium fasteners and chloride corrosion, Titanium fasteners chloride corrosion, Titanium fasteners chlorine corrosion, Titanium fasteners for chloride corrosion, Titanium fasteners for chloride resistance, titanium screws and chloride corrosion, Titanium screws chloride corrosion, Titanium screws chlorine corrosion, Titanium screws for chloride corrosion, Titanium screws for chloride resistance Leave a comment
Salt water is great for swimming, but provides industry a wide range of corrosion challenges from marine vessels to desalination plants, and even off-shore oil. The good news is there are several materials that perform very well in these environments. This newsletter compares them on their salt water corrosion resistance … Continue reading
Posted in Blog, Corrosion Resistance, Specialty Metal Fasteners Tagged AL6XN bolts for salt water corrosion, AL6XN fasteners for salt water corrosion, AL6XN for salt water corrosion, AL6XN screws for salt water corrosion, Monel bolts for salt water corrosion, Monel fasteners for salt water corrosion, Monel for salt water, Monel screws for salt water corrosion, titanium bolts for salt water corrosion, titanium bolts for salt water resistance, titanium fasteners for salt water resistance, Titanium screws for salt water corrosion, titanium screws for salt water resistance 1 Comment
Q: I have a laboratory applications that uses about 25% sulfuric acid at room temperature to 100F. I’d like to use a polymer rather than a metal if possible. I tried PTFE screws because I thought they were corrosion resistant, but they need to be replaced often because they can’t … Continue reading
Posted in Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Technical Questions Tagged PTFE bolts for corrosion resistance, PTFE bolts for sulfuric acid, PTFE fasteners for sulfuric acid, PTFE screws for corrosion resistance, PTFE screws for sulfuric acid, PVDF bolts for corrosion resistance, PVDF bolts for sulfuric acid, PVDF fasteners for corrosion resistance, PVDF fasteners for sulfuric acid, PVDF screws for corrosion resistance, PVDF screws for sulfuric acid Leave a comment
Extreme high strength fasteners made from advanced alloys allow industries such as aerospace, mining, and oil & gas to push the limits of what is possible. With requirements of ultimate tensile strengths beyond 200ksi this newsletter reviews these materials, their specific traits and niches. 17-4 PH Age hardened, 17-4PH … Continue reading
Posted in Application, Blog, High Strength, Material, Specialty Metal Fasteners Tagged 17-4 PH bolts for high strength, 17-4 PH screws for high strength, 17-4PH bolts for high strength, 17-4PH screws for high strength, High strength bolts, High Strength Fasteners, High strength screws, Inconel 718 bolts for high strength, Inconel 718 screws for high strength, MP159 bolts for high strength, MP159 fasteners for high strength, MP159 screws for high temperature, MP35N bolts for high strength, MP35N screws for high strength, Waspaloy bolts for high strength, Waspaloy screws for high strength 2 Comments
From thermal processing and furnace applications to the extreme demands of aerospace, several high temperature alloys are available each with unique traits and capabilities. This brief newsletter will outline the primary fastener materials that are commonly used for excellent high temperature and oxidation resistance. Best High Temperature Oxidation Resistant Fasteners … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Blog, High Strength, High Temperature Resistance, Material, Specialty Metal Fasteners Tagged 310SS bolts for cyclic conditions, 310SS cyclic conditions, 310SS screws for cyclic conditions, A286 bolts for oxidation resistance, A286 fasteners for oxidation resistance, A286 screws for oxidation resistance, Alloy 330 bolts for high temperature oxidation, Alloy 330 bolts for high temperature oxidation resistance, Alloy 330 bolts for high temperatures, Alloy 330 screws for high temperatures, Bolts for cyclic conditions, bolts for high temperature oxidation resistance, bolts for oxidation and caburization resistance, bolts for oxidation resistance, Fasteners for cyclic conditions, fasteners for high temperature oxidation resistance, fasteners for oxidation resistance, Materials for cyclic conditions, Screws for cyclic conditions, screws for high temperature oxidation resistance, screws for oxidation and caburization resistance, screws for oxidation resistance 1 Comment
Q: I’m working with a process that requires a constant operating temperature of 450F. Do I need to use a metal screw or is there a polymer that can handle this? A: There are definitely polymers that can handle an environment of 450F. One option is a PEEK fastener. PEEK … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Technical Questions Tagged high temperature plastic fasteners, high temperature plastic screws, high temperature polymer fasteners, high temperature polymer screws, PEEK fasteners for high temperature, PEEK high temperature screws, PEEK screws for high temperatures, PEEK verse vespel for high temperatures, Plastic fasteners for high temperature, Plastic screws for high temperatures, Polymer fasteners for high temperature, Polymer screws for high temperature, Vespel fasteners for high temperature, Vespel screws for high temperatures, Vespel vs PEEK for high temperatures Leave a comment
I’m running some laboratory testing in a mixed acid environment and would like to use a corrosion resistant polymer as apposed to a metal. I’ve tried PEEK screws but am still struggling a bit with some acids. Is there anything better? PEEK screws provide reasonable corrosion resistance to most acids … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, Technical Questions Tagged FDA approved polymer fasteners, polymer corrosion resistant fasteners, polymer screws for acid resistance, PTFE acid resistant fasteners, PTFE acid resistant screws, PTFE corrosion resistant fasteners, PTFE corrosion resistant screws, PTFE fasteners for acid resistance, PTFE fasteners for corrosion, PTFE for corrosion, PTFE screws for acid resistance, screws for laboratory acids Leave a comment
Q: I have an application where I need a non-metal fastener because of insulation and magnetic issues. The problem is that it also needs to be able to retain strength at about 520°F. Should I use a ceramic? A: Ceramic fasteners are definitely not necessary at these temperatures, although they … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Material, Non-Conductive, Technical Questions Tagged Torlon fasteners, Torlon fasteners for high strength, torlon fasteners for high temperature, torlon fasteners insulating properties, Torlon for high strength, torlon polymer fasteners, torlon polymer screws, Torlon Screws, Torlon screws for high strength, torlon screws for high temperture, torlon screws insulating properties Leave a comment
Q: I need a fastener that is very low weight and offers good wear resistance for a robotics application. I need about 40 ksi in strength. A: For your application I would actually suggest an engineered polymer fasteners since your strength requirement isn’t high enough to necessitate a metal . … Continue reading
Posted in Application, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Lightweight, Material, Technical Questions Tagged Fasteners for lightweight, High strength polymer fasteners, high strength polymer screws, PEEK Carbon Fiber Fastener, PEEK fastener, PEEK FAsteners for robotics, PEEK reinforced fastener, PEEK screws for lightweight, PEEK screws for Robotics, Screws for lightweight Leave a comment
Q: I am looking for some high tensile strength studs with good electricity resistance. I think zirconia of aluminia material will be suitable but I am open for suggestions. The studs would be about 5 inches long. A: Probably ceramics fasteners are not the best choice for this situation. It … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Engineered Polymer Fasteners, FAQs, High Strength, Non-Conductive, Technical Questions Tagged non-conductive bolts, non-conductive ceramic fasteners, non-conductive fasterns, non-conductive PEEK fasteners, non-conductive polymer fasteners, non-conductive screws Leave a comment
Q: I’m operating a FGD (Flue Gas Desulphurization) plant and am experiencing some mild corrosion on my scrubber bolting. I’m currently using Incoloy 825 bolts. It’s mild corrosion but non-the-less I’d like to have it cleared up before I get additional issues. Any suggestions? A: Since scrubber liquids and gases … Continue reading
Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners, Technical Questions Tagged Alloy 825, Alloy C276, FGD, FGD scrubber corrosion, FGD slurry corrosion, flue gas corosion resistance, flue gas desulfurization, Hastelloy C276, Incoloy 825, Inconel, Sulfuric Acid, Sulfuric Acid Corrosion, sulfuric acid protection Leave a comment
Q: I have a question regarding a type of fastener that can handle sterilization. What I need is a polymer if possible that can handle both steam and radiation sterilization processes, but doesn’t leach into my process. Contamination is an issue. A: You can definitely use a polymer for this … Continue reading
Posted in Application, Corrosion Resistance, Engineered Polymer Fasteners, FAQs, High Temperature Resistance, Technical Questions, Ultra Purity Tagged Hydrolysis resistance, PEEK, PEEK Screws, PTFE fastener, radiation resistance, steam resistance, Sterilization process, Sterlization resistance Leave a comment
Q: I’m designing laboratory equipment that will be utilized at 325-400F and I need screws that have immunity to organics and low concentrations of acids, as well be FDA approved. Would that be a ceramic? A: You probably don’t want a ceramic screw. Though they are corrosion resistant and offer … Continue reading
Nickel alloys are a special class of metals containing high levels of nickel (often greater than 20%). They play a key role in industry for their unique combination of high strength, corrosion resistance to harsh acids (like hydrochloric and sulfuric) and high temperature stability. This two-part newsletter will help summarize the distinct benefits of the … Continue reading
Posted in Application, Blog, Corrosion Resistance, Material, Specialty Metal Fasteners Tagged AL-6XN, AL6XN, Alloy 20, Alloy 400, Alloy K500, Carpenter 20, Corrosion, corrosion resistance, Monel, Monel 400, Monel K500, nickel, nickel alloys, Salt Water Resistance, Sea Water Resistance, Specialty Metals, Sulfuric Acid Leave a comment
Oilfields are subjected to a diversity of corrosive elements including carbonic acids, sour gas (H2S), and fracking/stimulant acids such as hydrochloric and hydrofluoric acid. Naphthenic acids and simple organic acids are also found in crude oil extraction. In conjunction to acids, these environments contain sand and other abrasive elements which … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, High Temperature Resistance, Specialty Metal Fasteners Tagged fracking corrosion, Hastelloy, hastelloy C2000, Hastelloy C276, Hydrochloric Acid, Hydrochloric acid resistance, Hydrofluoric acid, Incoloy, Incoloy 825, Incoloy 925, oil & gas corrosion, Oil Corrosion, sour gas, sour gas well, sulfur corrosion, Sulfur corrosion resistance, sulfur-induced stress cracking 1 Comment
Q: I am looking for a suitable fastener for use in a high heat furnace that is running at 2000F but the actual hearth wear flames go up to 3000F. The furnace is not under vacuum and has a normal atmosphere. We are finding that the 304 bolts are failing … Continue reading
Q: I’m building some lab equipment what will be housing hydrochloric acid. I need a non-metal fastener that is corrosion resistant . Can you make a recommendation? A: In terms of a material that is not metallic and can handle hydrochloric acid, I would suggest either PTFE or PVDF. PTFE … Continue reading
Extreme bolt offers hose clamps in Titanium and Hastelloy C276. This newsletter overviews the two styles available – worm drive and medium duty – as well as highlight what materials are best for your application. Titanium Grade 2 hose clamps are in stock and available in the sizes shown here. Hastelloy C276 hose clamps are custom made to order … Continue reading
Posted in Blog, Corrosion Resistance, Lightweight, Specialty Metal Fasteners Tagged Acid resistant hose clamp, Alloy C276, Corrosion resistant hose clamp, Hastelloy, Hastelloy C276, Hose clamp, Medium duty hose clamp, Titanium, Titanium Gr2, Titanium Grade 2, Worm drive, Worm drive hose clamp Leave a comment
Q: I was planning on using Hastelloy C276 in hot sulfuric acid. It would be approximately 50% concentration around 100F +/- 10 degrees. Will this be okay? I’m just concerned because I read that it cannot handle strong oxidizing environments and I’ll be using it in an application where its … Continue reading
Q: I have an application where I need pan head, insulating, high vacuum compatible, screw. It will also need to be usable at a service temperature up to 150C. Do I need a ceramic? A: Though ceramics are excellent insulators, they are usually only used for high temperature applications, where … Continue reading
Posted in Advanced Ceramic Fasteners, Application, Engineered Polymer Fasteners, FAQs, Non-Conductive, Technical Questions Tagged Alumina, Insulator, PEEK, PVDF, vacuum Leave a comment
Q: I’m looking for a chemically resistant polymer that can withstand chlorine and chlorine dioxide as well as a decent amount of weight and tension (around 27 lbs of weigh). Can you suggest a material? A: Of course it depends on the concentrations and temperatures you are operating at but generally … Continue reading
Q: I’ve got in a high pressure sour gas well. We’ve been having trouble with 316 stainless steel components breaking. I need a solution but not sure what to use. A: High pressures and sour gas combined can cause cracking and corrosion in most standard stainless and alloy steels. Depending … Continue reading
Posted in Application, High Strength Tagged 17-4 PH, 17-4PH, 316, 316SS, MP35N, sour gas, Stress Corrosion Cracking Leave a comment
They rhyme, are both used in extreme environments, and are both nickel metal alloys, but Monel and Inconel are actually very different. But how? Let’s start with basic chemistry. Monel is a nickel-copper alloy and Inconel is a nickel-chromium alloy. So what does that mean for your extreme application? We … Continue reading
Posted in Application, Blog, Corrosion Resistance, High Strength, High Temperature Resistance, Specialty Metal Fasteners Tagged Alloy 400, Alloy 625, Corrosion, hastelloy C2000, High Temperature, Hydrofluoric acid, Inconel, Inconel 625, Monel, Monel 400, saltwater corrosion, sea water corrosion 1 Comment
Q: How does creep occur and what polymer is best to prevent this? A: Creep is the permanent deformation of the material caused by constant load or stress, usually accompanied by constant high temperature. This can result in permanent changes of the fastener shape as well weakening and fracturing of the … Continue reading
Posted in Engineered Polymer Fasteners, FAQs, High Strength, Technical Questions Tagged creep resistant, PEEK, polymers screws Leave a comment
Q: I have a high pressure application with HCl at fluctuating temperatures. Can you recommend the best flange to provide a safe secure joint? A: Hands down, the weld neck flange is best for these types of hazardous, high pressure applications. Weld neck flanges are easily identified by their long … Continue reading
Q: When do you recommend to use a threaded flange? I need a flange that can be changed easily & frequently. A: After speaking with the customer, I found out that he has a pilot plant where he will be frequently changing parts. In this case a threaded flange is … Continue reading
Posted in Corrosion Resistance, FAQs, High Strength, High Temperature Resistance, Lightweight, Non-Conductive, Specialty Metal Fasteners, Technical Questions, Ultra Purity, Uncategorized Tagged dangerous application, flammable application, flange, pilot process, small pipe diameters, tapered pipe thread, threaded flange Leave a comment
Q: When is it best to use a lap joint flange? A: Lap joint flanges are good for very expensive materials like tantalum and zirconium and other specialty alloys like Hastelloy or Inconel due to reduced cost of sleeve vs solid flange. Lap joint flanges are unique in that they … Continue reading
Posted in Corrosion Resistance, FAQs, Specialty Metal Fasteners, Technical Questions Tagged Lap Joint Flange Leave a comment
Q: What advantages does Zirconia have over Alumina? A: Usually for most high temperature or electric insulator applications where ceramics are needed, alumina ceramic fasteners are the most popular choice due to their properties and relatively affordable price compared to zirconia fasteners. However sometimes the extreme properties of zirconia fasteners … Continue reading
Q: Need to replace a standard steel washer with a non-conductive material. A: After speaking with this customer, I learned that he needed to replace a standard steel washer with a non-conductive material for a critical bolted joint. These washers needed to withstand 70°C temperatures while maintaining preload. He … Continue reading
Q: Can you provide alternative for a nylon pan head screw? A: Here the customer needed an alternative to nylon. Resistance to electrical fields was a primary concern. In addition, he also needed a material that had a better dissipation factor than nylon. In this situation we would recommend PEEK. It … Continue reading
Q: Need help with specific needs regarding Polyimide fasteners and their high temperature capabilities A: This Italian company was developing a new client oven. They were interested in Polyimide fasteners and their high temperature capabilities. In particular they needed: Usability to 300°C Capability with metal connections Heat and electric … Continue reading
Q: Why does Zirconia cost more than Alumina? A: 1.) Raw material cost. Alumina is far more abundant, whereas Yttrium oxide which is a stabilizer for Zirconia ceramic, is a rare earth element. 2.) Shaping costs. Due to its higher density it takes approximately 10x longer to grind down … Continue reading
Posted in Advanced Ceramic Fasteners, FAQs, High Temperature Resistance, Technical Questions Tagged Alumina, Zirconia Leave a comment
Q: Polyimide / Vespel fasteners and their high temperature capabilities A: This client is developing a new oven application and was interested in Polyimide fasteners and their high temperature capabilities. In particular they needed: