Tag Archives: H2SO4

Hastelloy vs Tantalum Bolts for Sulfuric Acid Corrosion in Lithium Extraction

Posted on January 3, 2018 by dean

Q:  I’m running a lithium extraction process where a mineral called spodumene is roasted in a mixture of sulphuric acid (95-97%) at at about 150°C to form lithium sulfate. I’ve to use Hastelloy C276 for some process equipment but I’m still experiencing corrosion. Please help. A:  Hastelloy C276 bolts typically … Continue reading →

Posted in Application, Corrosion Resistance, FAQs, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , , | Leave a comment

Bolts for municipal waste incinerator: Hastelloy protects from HCl corrosion

Posted on December 12, 2017 by dean

Q:  I’m running a municipal solid waste incinerator and am having trouble with corrosion from a combination of hydrochloric acid and sulfuric acid that is derived from chloride and sulfur containing compounds in the waste fuel stream. I was using Duplex steel bolts for the chloride corrosion but they aren’t holding … Continue reading →

Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , , , | Leave a comment

Corrosion resistance of Inconel 625 bolts vs Hastelloy C276

Posted on August 28, 2017 by dean

Q: Inconel 625 and Hastelloy C276 bolts seem to have similar Nickel content. Does this mean these fasteners will perform the same in a corrosive environment? A: Inconel 625 and Hastelloy C276 bolts do offer similar corrosion resistance but Hastelloy C276 has a slight edge in many acidic environements, especially … Continue reading →

Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , , , , | Leave a comment

Alloy 20 fasteners for sulfuric acid corrosion

Posted on August 23, 2017 by dean

Q: I’m working with boiling sulfuric acid and tried Alloy 20 for some of my bolting but am having corrosion. I’m confused as I thought that is what they are best for. Any suggestions. A: You are right Alloy 20 does typically perform very well in sulfuric acid and even … Continue reading →

Posted in Application, FAQs, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , , | Leave a comment

Most Common of Hastelloy Fasteners Reviewed

Posted on July 25, 2017 by dean

hastelloy-grades_smallHastelloy alloys have long been the gold standard of corrosion resistant bolts; only out performed by metals like Zirconium and Tantalum. This family of high performance nickel alloys can handle strong acids like hydrochloric, sulfuric, acetic, formic and phosphoric acids, yet each grade actually exhibits its own strengths in dealing with specific acids and niche environments. … Continue reading →

Posted in Blog, Material, Specialty Metal Fasteners, Uncategorized | Tagged , , , , , , , , , , , , , , , , , , | Leave a comment

Hastelloy C276 bolts in hot sulfuric acid

Posted on July 12, 2017 by dean

Inline image 1Q: I was planning on using Hastelloy C276 in hot sulfuric acid. It would be approximately 50% concentration around 100F +/- 10 degrees. Will this be okay? I’m just concerned because I read that it cannot handle strong oxidizing environments and I’ll be using it in an application where its … Continue reading →

Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , | Leave a comment

Zirconium fasteners exposed to downstream oxidizers

Posted on May 25, 2017 by dean

Q: I’m using zirconium fasteners in a sulfuric acid process but they are showing corrosion. I’m not sure why as I’m well below boiling and only using 40% concentration. There may be some downstream contaminants, but not much. Any ideas? A: It is most likely the contaminants that are causing … Continue reading →

Posted in Application, Corrosion Resistance, FAQs, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , , , , , , , | Leave a comment

Inconel 625 vs. 718 bolts: Which Is Best for Your Application?

Posted on March 6, 2017 by dean

Inconel fasteners are commonly used for extreme environments and come in various “flavors” depending on the needs of the application. This brief paper will give you a quick comparison of the two most popular grades, Inconel 625 and Inconel 718 to help you choose the best material.

Posted in Blog | Tagged , , , , , , , , , , , , | 1 Comment

Fasteners for Sulfuric Acid (H2SO4)

Posted on November 11, 2015 by dean

Corrosion Resistant FastenersSulfuric Acid (H2SO4) is one of the most widely used and industrially important acids in modern society, being an essential component in the production of polymers, fuels, pharmaceuticals,  electronics, and mining. While sulfuric acid is commonly used, enabling fasteners to survive in this environment is not always an easy task. To help you tackle this feat, … Continue reading →

Posted in Blog | Tagged , , , , , , , , , , | Leave a comment